Electronics component help

[Xsannz]

Here is a picture of the existing components back: link http://m.imgur.com/gallery/pFE6jRA

It is a 50k 1 turn potentiometer with center detent, 6mm diameter knurled shaft, 9mm length and a spst push button momentary switch. I haven't had any luck trying to determine the manufacturer of the component or a replacement that ticks all of the above boxes. If anyone is able to help, it would be greatly appreciated!

[Craigor]

I posted here, and then xsannz deleted my post

In light of this am hereby declaring this thread de-railed

Who likes potatoes?

[Clin]

fuck yes

[Xsannz]

I posted here, and then xsannz deleted my post

In light of this am hereby declaring this thread de-railed

Who likes potatoes?

pffft, potatoes,,, got fries with that...

[Pigdog]

To like the potato you must become the potato.

Are you ready for this journey??

[Lias]

[Retardobot]

MASHED WITH CHEESE UP IN THIS!

[private_hell]

Its a Piher product. im currently hunting to see if i can find a replacement switch.

edit: well shit. they dont make it easy. i'll try again tomorrow at work - to either find a match or one that will do the exact same thing

[Xsannz]

Its a Piher product. im currently hunting to see if i can find a replacement switch.

edit: well shit. they dont make it easy. i'll try again tomorrow at work - to either find a match or one that will do the exact same thing

dude that would be legend

not worried about dimensions just that it has the functionality as above and a knurled shaft

[Xsannz]

 - - Updated - - -

Additional photos

http://iforce.co.nz/i/3i1h3tfi.4cu.jpg
http://iforce.co.nz/i/h12rf032.n2p.jpg

[Xsannz]

got a reply from potentiometer.com, R technical Australia and they all do custom stackable units, that they cant make a center detent with momentarty switch.

but some bastard must have done it, since i have 2 of them in the device.

[ArtanisNZ]

PANASONIC - EVU-E3JFK4B54 have a look at this?

[Xsannz]

PANASONIC - EVU-E3JFK4B54 have a look at this?

danm close, but no center dentent, which i really need to be able to pause between a + axis and a -axis

ok so

momentary push is the switch type,  the detent is not switched its just a mid position, as far as i know,

i might break out the multimeter tonight and just check the centre detent is not switched as well.

[ArtanisNZ]

My spec sheet says they have mid point detent. And I think I have used them for audio balance adjustment on a mixing board I've fixed for a mate.

[Xsannz]

My spec sheet says they have mid point detent.

yeah but i think they have the switch on the midpoint detent.  but no push momentary switch..

[ArtanisNZ]

Yeah sounds like you've got a pure custom part on your hands. Very slim chance you be able to find a replacement sort of raid saiteks factory.

[Clin]

Wait a minute, is this broken thingy in the yoke you're selling?

[Xsannz]

Wait a minute, is this broken thingy in the yoke you're selling?

NOPE.

I have the warranty replacement ones in a box thats what i am selling, the parts are to fix a mates X52 Pro

the parts are in the x52 pro and the X55 are the same in the throttle units

i am selling the X55, but i would love to be able to find the parts as i started an arduino project to build my own flight panel.


since the Warthog setup i have doesnt have enough momentary toggles which most games use rather than on of hold style toggles.

[Retardobot]

What are you doing posting about weird electricity shit in a potato thread?

[Xsannz]

What are you doing posting about weird electricity shit in a potato thread?

because

[Retardobot]

Well what do you know, it's a potato chip.

[Clin]

[Pigdog]

[Craigor]

Well what do you know, it's a potato chip.

I lold